Motor MAN D2676LE423 (i6-800) marine engine pentru MAN
Hörsching7279 km to "United States/Columbus"
Dacă ați decis achiziționarea echipamentului la un preț mic, trebuie să fiți sigur că persoana cu care comunicați este un vânzător real. Aflați toate informațiile disponibile cu privire la proprietarul echipamentului. O metodă de înșelăciune este aceea de a se prezenta ca o societate existentă în mod real. În caz de îndoială, vă rugăm să luați legătura cu noi prin formularul de feedback, pentru alte controale.
Înainte de a decide o achiziție, examinați cu atenție diferite oferte de vânzare pentru a cunoaște costul mediu al modelului ales. Dacă prețul din oferta care vă place este mult mai mic față de alte oferte asemănătoare, gândiți-vă bine. O diferență de preț importantă poate indica defecte ascunse sau o tentativă a vânzătorului de a comite o înșelăciune.
Nu cumpărați produse care au prețuri mult diferite față de prețul mediu al altor produse asemănătoare
Nu dați acordul la plata unor cauțiuni suspecte sau plăți anticipate ale mărfurilor. În caz de îndoieli, clarificați amănuntele, solicitați mai multe fotografii și documente privind mașina, verificați autenticitatea documentelor, puneți întrebări.
Cel mai răspândit tip de înșelăciune. Vânzătorii necinstiți pot cere o anumită sumă din avans, pentru ”rezervarea” dreptului de achiziționare a mijlocului. În acest mod ei strâng o mare sumă de bani, după care dispar, fără a putea fi contactați.
- Transferul plății anticipate pe card
- Nu efectuați plata anticipată fără semnarea documentelor care să ateste procesul de transfer de bani, dacă în timpul tratativei vânzătorul are îndoieli.
- Transfer în contul ”curatorului”
- O astfel de solicitare trebuie să vă alarmeze, foarte probabil comunicați cu o persoană care urmărește să vă înșele.
- Transferul în contul societății cu un nume asemănător
- Atenție, persoanele rău intenționate se pot ascunde în spatele unor societăți renumite, aducând mici modificări numelui societății. Nu efectuați transfer de bani dacă numele societății este dubios.
- Înlocuirea propriilor date în factura societății reale
- Înainte de efectua transferul de bani, vă rugăm să verificați corectitudinea datelor bancare și dacă acestea aparțin societății indicate.
Contactează vânzătorul
+358 50 53...
Arată
+358 50 5345498
+358 9 231...
Arată
+358 9 23165797
Austria 
Austria, Hörsching
Austria, Hörsching
Austria, Hörsching
Austria, Hörsching
Austria, Hörsching
Austria, Hörsching
Austria, Hörsching
Austria, Hörsching
Austria, Hörsching
motor
Austria, Hörsching
China, Baoding, Hebei
Germania, KI
Turcia, İZMİR/TURKEY
Belgia, TEMPLOUX
Turcia, İZMİR/TURKEY
Lituania, Kaunas
Belgia, Hamont
Marea Britanie, Dudley
02 units
Marine diesel engine
D2676LE423 (i6-800)
Performance data .
Rated power 588 kW
Rated power 800 PS
Speed 2300 rpm
Bore 126 mm
Stroke 166 mm
Displacement 12,42 liter
Rated torque 2441 Nm
Maximum torque 2674 Nm
at speed 1400-2000 rpm
Engine description
Operation profile up to 1000 hours per year at a maximum of 20 % of time at full load | average load < 50 %
Construction four-stroke marine diesel engine, direct injection, SAE 1 flywheel housing
Cylinders 6 cylinders in line, single cylinder heads with wet replaceable cylinder liners
Air system single-stage turbocharger with charge air intercooler and wastegate
Cooling system seawater cooled charge air cooler and plate heat exchanger by rubber impeller pump
Oil system force-feed lubrication by gear pump, lubricating oil cooler in cooling water circuit of the engine
Fuel system Common Rail injection system with high pressure pump and EDC control, fuel to DIN EN 590
Auxiliary PTO PTO for hydraulic pump 16 cm.
Alternator three-phase generator with rectifier and transistorized governor, 28 V, 110 A
Starting system solenoid operated electric starter, 24 V, 5.5 kW
Service oil change interval 400 operating hours, average TBO 5.000 operating hours
Classification ---
Exhaust status IMO Tier II, RCD 2013/53/EC, RCD 94/25/EC, EPA Tier 3 recreational, 97/68/EC
. values at rated power . Tolerance +5% according to ISO 3046, diesel fuel to DIN EN 590 . values on propeller curve
D2676LE423 (i6-800)
A - overall width............ 986 B - overall length........... 1795 C - overall height........... 1096 D - above crank shaft.... 674 E - length to flywheel.... 1527 Engine weight (dry)....... 1215
02 units
Marine diesel engine
D2676LE423 (i6-800)
Performance data .
Rated power 588 kW
Rated power 800 PS
Speed 2300 rpm
Bore 126 mm
Stroke 166 mm
Displacement 12,42 liter
Rated torque 2441 Nm
Maximum torque 2674 Nm
at speed 1400-2000 rpm
Engine description
Operation profile up to 1000 hours per year at a maximum of 20 % of time at full load | average load < 50 %
Construction four-stroke marine diesel engine, direct injection, SAE 1 flywheel housing
Cylinders 6 cylinders in line, single cylinder heads with wet replaceable cylinder liners
Air system single-stage turbocharger with charge air intercooler and wastegate
Cooling system seawater cooled charge air cooler and plate heat exchanger by rubber impeller pump
Oil system force-feed lubrication by gear pump, lubricating oil cooler in cooling water circuit of the engine
Fuel system Common Rail injection system with high pressure pump and EDC control, fuel to DIN EN 590
Auxiliary PTO PTO for hydraulic pump 16 cm.
Alternator three-phase generator with rectifier and transistorized governor, 28 V, 110 A
Starting system solenoid operated electric starter, 24 V, 5.5 kW
Service oil change interval 400 operating hours, average TBO 5.000 operating hours
Classification ---
Exhaust status IMO Tier II, RCD 2013/53/EC, RCD 94/25/EC, EPA Tier 3 recreational, 97/68/EC
. values at rated power . Tolerance +5% according to ISO 3046, diesel fuel to DIN EN 590 . values on propeller curve
D2676LE423 (i6-800)
A - overall width............ 986 B - overall length........... 1795 C - overall height........... 1096 D - above crank shaft.... 674 E - length to flywheel.... 1527 Engine weight (dry)....... 1215
02 units
Marine diesel engine
D2676LE423 (i6-800)
Performance data .
Rated power 588 kW
Rated power 800 PS
Speed 2300 rpm
Bore 126 mm
Stroke 166 mm
Displacement 12,42 liter
Rated torque 2441 Nm
Maximum torque 2674 Nm
at speed 1400-2000 rpm
Engine description
Operation profile up to 1000 hours per year at a maximum of 20 % of time at full load | average load < 50 %
Construction four-stroke marine diesel engine, direct injection, SAE 1 flywheel housing
Cylinders 6 cylinders in line, single cylinder heads with wet replaceable cylinder liners
Air system single-stage turbocharger with charge air intercooler and wastegate
Cooling system seawater cooled charge air cooler and plate heat exchanger by rubber impeller pump
Oil system force-feed lubrication by gear pump, lubricating oil cooler in cooling water circuit of the engine
Fuel system Common Rail injection system with high pressure pump and EDC control, fuel to DIN EN 590
Auxiliary PTO PTO for hydraulic pump 16 cm.
Alternator three-phase generator with rectifier and transistorized governor, 28 V, 110 A
Starting system solenoid operated electric starter, 24 V, 5.5 kW
Service oil change interval 400 operating hours, average TBO 5.000 operating hours
Classification ---
Exhaust status IMO Tier II, RCD 2013/53/EC, RCD 94/25/EC, EPA Tier 3 recreational, 97/68/EC
. values at rated power . Tolerance +5% according to ISO 3046, diesel fuel to DIN EN 590 . values on propeller curve
D2676LE423 (i6-800)
A - overall width............ 986 B - overall length........... 1795 C - overall height........... 1096 D - above crank shaft.... 674 E - length to flywheel.... 1527 Engine weight (dry)....... 1215
02 units
Marine diesel engine
D2676LE423 (i6-800)
Performance data .
Rated power 588 kW
Rated power 800 PS
Speed 2300 rpm
Bore 126 mm
Stroke 166 mm
Displacement 12,42 liter
Rated torque 2441 Nm
Maximum torque 2674 Nm
at speed 1400-2000 rpm
Engine description
Operation profile up to 1000 hours per year at a maximum of 20 % of time at full load | average load < 50 %
Construction four-stroke marine diesel engine, direct injection, SAE 1 flywheel housing
Cylinders 6 cylinders in line, single cylinder heads with wet replaceable cylinder liners
Air system single-stage turbocharger with charge air intercooler and wastegate
Cooling system seawater cooled charge air cooler and plate heat exchanger by rubber impeller pump
Oil system force-feed lubrication by gear pump, lubricating oil cooler in cooling water circuit of the engine
Fuel system Common Rail injection system with high pressure pump and EDC control, fuel to DIN EN 590
Auxiliary PTO PTO for hydraulic pump 16 cm.
Alternator three-phase generator with rectifier and transistorized governor, 28 V, 110 A
Starting system solenoid operated electric starter, 24 V, 5.5 kW
Service oil change interval 400 operating hours, average TBO 5.000 operating hours
Classification ---
Exhaust status IMO Tier II, RCD 2013/53/EC, RCD 94/25/EC, EPA Tier 3 recreational, 97/68/EC
. values at rated power . Tolerance +5% according to ISO 3046, diesel fuel to DIN EN 590 . values on propeller curve
D2676LE423 (i6-800)
A - overall width............ 986 B - overall length........... 1795 C - overall height........... 1096 D - above crank shaft.... 674 E - length to flywheel.... 1527 Engine weight (dry)....... 1215
02 units
Marine diesel engine
D2676LE423 (i6-800)
Performance data .
Rated power 588 kW
Rated power 800 PS
Speed 2300 rpm
Bore 126 mm
Stroke 166 mm
Displacement 12,42 liter
Rated torque 2441 Nm
Maximum torque 2674 Nm
at speed 1400-2000 rpm
Engine description
Operation profile up to 1000 hours per year at a maximum of 20 % of time at full load | average load < 50 %
Construction four-stroke marine diesel engine, direct injection, SAE 1 flywheel housing
Cylinders 6 cylinders in line, single cylinder heads with wet replaceable cylinder liners
Air system single-stage turbocharger with charge air intercooler and wastegate
Cooling system seawater cooled charge air cooler and plate heat exchanger by rubber impeller pump
Oil system force-feed lubrication by gear pump, lubricating oil cooler in cooling water circuit of the engine
Fuel system Common Rail injection system with high pressure pump and EDC control, fuel to DIN EN 590
Auxiliary PTO PTO for hydraulic pump 16 cm.
Alternator three-phase generator with rectifier and transistorized governor, 28 V, 110 A
Starting system solenoid operated electric starter, 24 V, 5.5 kW
Service oil change interval 400 operating hours, average TBO 5.000 operating hours
Classification ---
Exhaust status IMO Tier II, RCD 2013/53/EC, RCD 94/25/EC, EPA Tier 3 recreational, 97/68/EC
. values at rated power . Tolerance +5% according to ISO 3046, diesel fuel to DIN EN 590 . values on propeller curve
D2676LE423 (i6-800)
A - overall width............ 986 B - overall length........... 1795 C - overall height........... 1096 D - above crank shaft.... 674 E - length to flywheel.... 1527 Engine weight (dry)....... 1215
02 units
Marine diesel engine
D2676LE423 (i6-800)
Performance data .
Rated power 588 kW
Rated power 800 PS
Speed 2300 rpm
Bore 126 mm
Stroke 166 mm
Displacement 12,42 liter
Rated torque 2441 Nm
Maximum torque 2674 Nm
at speed 1400-2000 rpm
Engine description
Operation profile up to 1000 hours per year at a maximum of 20 % of time at full load | average load < 50 %
Construction four-stroke marine diesel engine, direct injection, SAE 1 flywheel housing
Cylinders 6 cylinders in line, single cylinder heads with wet replaceable cylinder liners
Air system single-stage turbocharger with charge air intercooler and wastegate
Cooling system seawater cooled charge air cooler and plate heat exchanger by rubber impeller pump
Oil system force-feed lubrication by gear pump, lubricating oil cooler in cooling water circuit of the engine
Fuel system Common Rail injection system with high pressure pump and EDC control, fuel to DIN EN 590
Auxiliary PTO PTO for hydraulic pump 16 cm.
Alternator three-phase generator with rectifier and transistorized governor, 28 V, 110 A
Starting system solenoid operated electric starter, 24 V, 5.5 kW
Service oil change interval 400 operating hours, average TBO 5.000 operating hours
Classification ---
Exhaust status IMO Tier II, RCD 2013/53/EC, RCD 94/25/EC, EPA Tier 3 recreational, 97/68/EC
. values at rated power . Tolerance +5% according to ISO 3046, diesel fuel to DIN EN 590 . values on propeller curve
D2676LE423 (i6-800)
A - overall width............ 986 B - overall length........... 1795 C - overall height........... 1096 D - above crank shaft.... 674 E - length to flywheel.... 1527 Engine weight (dry)....... 1215
02 units
Marine diesel engine
D2676LE423 (i6-800)
Performance data .
Rated power 588 kW
Rated power 800 PS
Speed 2300 rpm
Bore 126 mm
Stroke 166 mm
Displacement 12,42 liter
Rated torque 2441 Nm
Maximum torque 2674 Nm
at speed 1400-2000 rpm
Engine description
Operation profile up to 1000 hours per year at a maximum of 20 % of time at full load | average load < 50 %
Construction four-stroke marine diesel engine, direct injection, SAE 1 flywheel housing
Cylinders 6 cylinders in line, single cylinder heads with wet replaceable cylinder liners
Air system single-stage turbocharger with charge air intercooler and wastegate
Cooling system seawater cooled charge air cooler and plate heat exchanger by rubber impeller pump
Oil system force-feed lubrication by gear pump, lubricating oil cooler in cooling water circuit of the engine
Fuel system Common Rail injection system with high pressure pump and EDC control, fuel to DIN EN 590
Auxiliary PTO PTO for hydraulic pump 16 cm.
Alternator three-phase generator with rectifier and transistorized governor, 28 V, 110 A
Starting system solenoid operated electric starter, 24 V, 5.5 kW
Service oil change interval 400 operating hours, average TBO 5.000 operating hours
Classification ---
Exhaust status IMO Tier II, RCD 2013/53/EC, RCD 94/25/EC, EPA Tier 3 recreational, 97/68/EC
. values at rated power . Tolerance +5% according to ISO 3046, diesel fuel to DIN EN 590 . values on propeller curve
D2676LE423 (i6-800)
A - overall width............ 986 B - overall length........... 1795 C - overall height........... 1096 D - above crank shaft.... 674 E - length to flywheel.... 1527 Engine weight (dry)....... 1215
02 units
Marine diesel engine
D2676LE423 (i6-800)
Performance data .
Rated power 588 kW
Rated power 800 PS
Speed 2300 rpm
Bore 126 mm
Stroke 166 mm
Displacement 12,42 liter
Rated torque 2441 Nm
Maximum torque 2674 Nm
at speed 1400-2000 rpm
Engine description
Operation profile up to 1000 hours per year at a maximum of 20 % of time at full load | average load < 50 %
Construction four-stroke marine diesel engine, direct injection, SAE 1 flywheel housing
Cylinders 6 cylinders in line, single cylinder heads with wet replaceable cylinder liners
Air system single-stage turbocharger with charge air intercooler and wastegate
Cooling system seawater cooled charge air cooler and plate heat exchanger by rubber impeller pump
Oil system force-feed lubrication by gear pump, lubricating oil cooler in cooling water circuit of the engine
Fuel system Common Rail injection system with high pressure pump and EDC control, fuel to DIN EN 590
Auxiliary PTO PTO for hydraulic pump 16 cm.
Alternator three-phase generator with rectifier and transistorized governor, 28 V, 110 A
Starting system solenoid operated electric starter, 24 V, 5.5 kW
Service oil change interval 400 operating hours, average TBO 5.000 operating hours
Classification ---
Exhaust status IMO Tier II, RCD 2013/53/EC, RCD 94/25/EC, EPA Tier 3 recreational, 97/68/EC
. values at rated power . Tolerance +5% according to ISO 3046, diesel fuel to DIN EN 590 . values on propeller curve
D2676LE423 (i6-800)
A - overall width............ 986 B - overall length........... 1795 C - overall height........... 1096 D - above crank shaft.... 674 E - length to flywheel.... 1527 Engine weight (dry)....... 1215
02 units
Marine diesel engine
D2676LE423 (i6-800)
Performance data .
Rated power 588 kW
Rated power 800 PS
Speed 2300 rpm
Bore 126 mm
Stroke 166 mm
Displacement 12,42 liter
Rated torque 2441 Nm
Maximum torque 2674 Nm
at speed 1400-2000 rpm
Engine description
Operation profile up to 1000 hours per year at a maximum of 20 % of time at full load | average load < 50 %
Construction four-stroke marine diesel engine, direct injection, SAE 1 flywheel housing
Cylinders 6 cylinders in line, single cylinder heads with wet replaceable cylinder liners
Air system single-stage turbocharger with charge air intercooler and wastegate
Cooling system seawater cooled charge air cooler and plate heat exchanger by rubber impeller pump
Oil system force-feed lubrication by gear pump, lubricating oil cooler in cooling water circuit of the engine
Fuel system Common Rail injection system with high pressure pump and EDC control, fuel to DIN EN 590
Auxiliary PTO PTO for hydraulic pump 16 cm.
Alternator three-phase generator with rectifier and transistorized governor, 28 V, 110 A
Starting system solenoid operated electric starter, 24 V, 5.5 kW
Service oil change interval 400 operating hours, average TBO 5.000 operating hours
Classification ---
Exhaust status IMO Tier II, RCD 2013/53/EC, RCD 94/25/EC, EPA Tier 3 recreational, 97/68/EC
. values at rated power . Tolerance +5% according to ISO 3046, diesel fuel to DIN EN 590 . values on propeller curve
D2676LE423 (i6-800)
A - overall width............ 986 B - overall length........... 1795 C - overall height........... 1096 D - above crank shaft.... 674 E - length to flywheel.... 1527 Engine weight (dry)....... 1215
02 units
Marine diesel engine
D2676LE423 (i6-800)
Performance data .
Rated power 588 kW
Rated power 800 PS
Speed 2300 rpm
Bore 126 mm
Stroke 166 mm
Displacement 12,42 liter
Rated torque 2441 Nm
Maximum torque 2674 Nm
at speed 1400-2000 rpm
Engine description
Operation profile up to 1000 hours per year at a maximum of 20 % of time at full load | average load < 50 %
Construction four-stroke marine diesel engine, direct injection, SAE 1 flywheel housing
Cylinders 6 cylinders in line, single cylinder heads with wet replaceable cylinder liners
Air system single-stage turbocharger with charge air intercooler and wastegate
Cooling system seawater cooled charge air cooler and plate heat exchanger by rubber impeller pump
Oil system force-feed lubrication by gear pump, lubricating oil cooler in cooling water circuit of the engine
Fuel system Common Rail injection system with high pressure pump and EDC control, fuel to DIN EN 590
Auxiliary PTO PTO for hydraulic pump 16 cm.
Alternator three-phase generator with rectifier and transistorized governor, 28 V, 110 A
Starting system solenoid operated electric starter, 24 V, 5.5 kW
Service oil change interval 400 operating hours, average TBO 5.000 operating hours
Classification ---
Exhaust status IMO Tier II, RCD 2013/53/EC, RCD 94/25/EC, EPA Tier 3 recreational, 97/68/EC
. values at rated power . Tolerance +5% according to ISO 3046, diesel fuel to DIN EN 590 . values on propeller curve
D2676LE423 (i6-800)
A - overall width............ 986 B - overall length........... 1795 C - overall height........... 1096 D - above crank shaft.... 674 E - length to flywheel.... 1527 Engine weight (dry)....... 1215
02 units
Marine diesel engine
D2676LE423 (i6-800)
Performance data .
Rated power 588 kW
Rated power 800 PS
Speed 2300 rpm
Bore 126 mm
Stroke 166 mm
Displacement 12,42 liter
Rated torque 2441 Nm
Maximum torque 2674 Nm
at speed 1400-2000 rpm
Engine description
Operation profile up to 1000 hours per year at a maximum of 20 % of time at full load | average load < 50 %
Construction four-stroke marine diesel engine, direct injection, SAE 1 flywheel housing
Cylinders 6 cylinders in line, single cylinder heads with wet replaceable cylinder liners
Air system single-stage turbocharger with charge air intercooler and wastegate
Cooling system seawater cooled charge air cooler and plate heat exchanger by rubber impeller pump
Oil system force-feed lubrication by gear pump, lubricating oil cooler in cooling water circuit of the engine
Fuel system Common Rail injection system with high pressure pump and EDC control, fuel to DIN EN 590
Auxiliary PTO PTO for hydraulic pump 16 cm.
Alternator three-phase generator with rectifier and transistorized governor, 28 V, 110 A
Starting system solenoid operated electric starter, 24 V, 5.5 kW
Service oil change interval 400 operating hours, average TBO 5.000 operating hours
Classification ---
Exhaust status IMO Tier II, RCD 2013/53/EC, RCD 94/25/EC, EPA Tier 3 recreational, 97/68/EC
. values at rated power . Tolerance +5% according to ISO 3046, diesel fuel to DIN EN 590 . values on propeller curve
D2676LE423 (i6-800)
A - overall width............ 986 B - overall length........... 1795 C - overall height........... 1096 D - above crank shaft.... 674 E - length to flywheel.... 1527 Engine weight (dry)....... 1215
02 units
Marine diesel engine
D2676LE423 (i6-800)
Performance data .
Rated power 588 kW
Rated power 800 PS
Speed 2300 rpm
Bore 126 mm
Stroke 166 mm
Displacement 12,42 liter
Rated torque 2441 Nm
Maximum torque 2674 Nm
at speed 1400-2000 rpm
Engine description
Operation profile up to 1000 hours per year at a maximum of 20 % of time at full load | average load < 50 %
Construction four-stroke marine diesel engine, direct injection, SAE 1 flywheel housing
Cylinders 6 cylinders in line, single cylinder heads with wet replaceable cylinder liners
Air system single-stage turbocharger with charge air intercooler and wastegate
Cooling system seawater cooled charge air cooler and plate heat exchanger by rubber impeller pump
Oil system force-feed lubrication by gear pump, lubricating oil cooler in cooling water circuit of the engine
Fuel system Common Rail injection system with high pressure pump and EDC control, fuel to DIN EN 590
Auxiliary PTO PTO for hydraulic pump 16 cm.
Alternator three-phase generator with rectifier and transistorized governor, 28 V, 110 A
Starting system solenoid operated electric starter, 24 V, 5.5 kW
Service oil change interval 400 operating hours, average TBO 5.000 operating hours
Classification ---
Exhaust status IMO Tier II, RCD 2013/53/EC, RCD 94/25/EC, EPA Tier 3 recreational, 97/68/EC
. values at rated power . Tolerance +5% according to ISO 3046, diesel fuel to DIN EN 590 . values on propeller curve
D2676LE423 (i6-800)
A - overall width............ 986 B - overall length........... 1795 C - overall height........... 1096 D - above crank shaft.... 674 E - length to flywheel.... 1527 Engine weight (dry)....... 1215
02 units
Marine diesel engine
D2676LE423 (i6-800)
Performance data .
Rated power 588 kW
Rated power 800 PS
Speed 2300 rpm
Bore 126 mm
Stroke 166 mm
Displacement 12,42 liter
Rated torque 2441 Nm
Maximum torque 2674 Nm
at speed 1400-2000 rpm
Engine description
Operation profile up to 1000 hours per year at a maximum of 20 % of time at full load | average load < 50 %
Construction four-stroke marine diesel engine, direct injection, SAE 1 flywheel housing
Cylinders 6 cylinders in line, single cylinder heads with wet replaceable cylinder liners
Air system single-stage turbocharger with charge air intercooler and wastegate
Cooling system seawater cooled charge air cooler and plate heat exchanger by rubber impeller pump
Oil system force-feed lubrication by gear pump, lubricating oil cooler in cooling water circuit of the engine
Fuel system Common Rail injection system with high pressure pump and EDC control, fuel to DIN EN 590
Auxiliary PTO PTO for hydraulic pump 16 cm.
Alternator three-phase generator with rectifier and transistorized governor, 28 V, 110 A
Starting system solenoid operated electric starter, 24 V, 5.5 kW
Service oil change interval 400 operating hours, average TBO 5.000 operating hours
Classification ---
Exhaust status IMO Tier II, RCD 2013/53/EC, RCD 94/25/EC, EPA Tier 3 recreational, 97/68/EC
. values at rated power . Tolerance +5% according to ISO 3046, diesel fuel to DIN EN 590 . values on propeller curve
D2676LE423 (i6-800)
A - overall width............ 986 B - overall length........... 1795 C - overall height........... 1096 D - above crank shaft.... 674 E - length to flywheel.... 1527 Engine weight (dry)....... 1215
02 units
Marine diesel engine
D2676LE423 (i6-800)
Performance data .
Rated power 588 kW
Rated power 800 PS
Speed 2300 rpm
Bore 126 mm
Stroke 166 mm
Displacement 12,42 liter
Rated torque 2441 Nm
Maximum torque 2674 Nm
at speed 1400-2000 rpm
Engine description
Operation profile up to 1000 hours per year at a maximum of 20 % of time at full load | average load < 50 %
Construction four-stroke marine diesel engine, direct injection, SAE 1 flywheel housing
Cylinders 6 cylinders in line, single cylinder heads with wet replaceable cylinder liners
Air system single-stage turbocharger with charge air intercooler and wastegate
Cooling system seawater cooled charge air cooler and plate heat exchanger by rubber impeller pump
Oil system force-feed lubrication by gear pump, lubricating oil cooler in cooling water circuit of the engine
Fuel system Common Rail injection system with high pressure pump and EDC control, fuel to DIN EN 590
Auxiliary PTO PTO for hydraulic pump 16 cm.
Alternator three-phase generator with rectifier and transistorized governor, 28 V, 110 A
Starting system solenoid operated electric starter, 24 V, 5.5 kW
Service oil change interval 400 operating hours, average TBO 5.000 operating hours
Classification ---
Exhaust status IMO Tier II, RCD 2013/53/EC, RCD 94/25/EC, EPA Tier 3 recreational, 97/68/EC
. values at rated power . Tolerance +5% according to ISO 3046, diesel fuel to DIN EN 590 . values on propeller curve
D2676LE423 (i6-800)
A - overall width............ 986 B - overall length........... 1795 C - overall height........... 1096 D - above crank shaft.... 674 E - length to flywheel.... 1527 Engine weight (dry)....... 1215